Browsing by Author "Ozolanta, Iveta"

Now showing 1 - 5 of 5
  • No Thumbnail Available
    Item
    Biomechanical properties of human dilated ascending aorta
    (2019-05-01) Brečs, Ivars; Stradiņš, Peteris; Kalejs, Martiņš; Strazdiņš, Uldis; Ozolanta, Iveta; Kasyanov, Vladimir; Rīga Stradiņš University; Biomehānikas zinātniskā laboratorija
    Aneurysms of ascending aorta are dilatation of the first part of the human aorta. They commonly show no clinical symptoms. This condition increases the risk of aorta dissection, which is a life-threatening condition. In this study we attempted to elucidate the changes in the biomechanical properties that occur in the dilated human ascending aorta. Fourteen specimens of ascending aorta wall were mechanically tested under a uniaxial tensile test. Two specimens from each ascending aorta anterior region were cut in longitudinal and circumferential directions. The samples were stretched until rupture of the sample occurred. The obtained experimental data were processed to determine maximal stress, maximal strain and the tangential modulus of elasticity in the linear part of the stress-strain curve. The obtained results showed a remarkable anisotropy of the ascending aorta tissue. We found higher strength of the tissue in the circumferential direction than in the longitudinal direction. There were no statistically significant differences between the strains of the samples. Tangential modulus of elasticity of the aortic samples in the longitudinal direction was significantly lower than the elastic modulus of the samples in the circumferential direction. The tissue in the circumferential direction is stronger and stiffer than in the longitudinal direction.
  • No Thumbnail Available
    Item
  • No Thumbnail Available
    Item
    Comparison of biomechanical and structural properties between human aortic and pulmonary valve
    (2004-09) Stradins, Peteris; Lacis, Romans; Ozolanta, Iveta; Purina, Biruta; Ose, Velta; Feldmane, Laila; Kasyanov, Vladimir; Department of Surgery; Biomehānikas zinātniskā laboratorija
    Objective: Pulmonary valve autografts have been reported as clinically effective for replacement of diseased aortic valve (Ross procedure). Published data about pulmonary valve mechanical and structural suitability as a long-term substitute for aortic valve are limited. The aim of this study was to compare aortic and pulmonary valve properties. Methods: Experimental studies of biomechanical properties and structure of aortic and pulmonary valves were carried out on pathologically unchanged human heart valves, collected from 11 cadaveric hearts. Biomechanical properties of 84 specimens (all valve elements: cusps, fibrous ring, commissures, sinotubular junction, sinuses) were investigated using uniaxial tensile tests. Ultrastructure was studied using transmission and scanning electron microscopy. Results: Ultimate stress in circumferential direction for pulmonary valve cusps is higher than for aortic valve (2.78±1.05 and 1.74±0.29 MPa, respectively). Ultimate stress in radial direction for pulmonary and aortic cusps is practically the same (0.29±0.06 and 0.32±0.04 MPa, respectively). In ultrastructural study, different layout and density in each construction element are determined. The aortic and pulmonary valves have common ultrastructural properties. Conclusions: Mechanical differences between aortic and pulmonary valve are minimal. Ultrastructural studies show that the aortic and pulmonary valves have similar structural elements and architecture. This investigation suggests that the pulmonary valve can be considered mechanically and structurally suitable for use as an aortic valve replacement.
  • No Thumbnail Available
    Item
    From Biomechanical Properties to Morphological Variations : Exploring the Interplay between Aortic Valve Cuspidity and Ascending Aortic Aneurysm
    (2024-07-19) Brečs, Ivars; Skuja, Sandra; Kasyanov, Vladimir; Groma, Valērija; Kalējs, Mārtiņš; Svirskis, Šimons; Ozolanta, Iveta; Stradiņš, Pēteris; Joint Laboratory of Electron Microscopy; Joint Laboratory of Traumatology and Orthopaedics; Faculty of Medicine; Institute of Microbiology and Virology
    Background: This research explores the biomechanical and structural characteristics of ascending thoracic aortic aneurysms (ATAAs), focusing on the differences between bicuspid aortic valve aneurysms (BAV-As) and tricuspid aortic valve aneurysms (TAV-As) with non-dilated aortas to identify specific traits of ATAAs. Methods: Clinical characteristics, laboratory indices, and imaging data from 26 adult patients operated on for aneurysms (BAV-A: n = 12; TAV-A: n = 14) and 13 controls were analyzed. Biomechanical parameters (maximal aortic diameter, strain, and stress) and structural analyses (collagen fiber organization, density, fragmentation, adipocyte deposits, and immune cell infiltration) were assessed. Results: Significant differences in biomechanical parameters were observed. Median maximal strain was 40.0% (control), 63.4% (BAV-A), and 45.3% (TAV-A); median maximal stress was 0.59 MPa (control), 0.78 MPa (BAV-A), and 0.48 MPa (TAV-A). BAV-A showed higher tangential modulus and smaller diameter, with substantial collagen fragmentation ( p < 0.001 vs. TAV and controls). TAV-A exhibited increased collagen density ( p = 0.025), thickening between media and adventitia layers, and disorganized fibers ( p = 0.036). BAV-A patients had elevated adipocyte deposits and immune cell infiltration. Conclusions: This study highlights distinct pathological profiles associated with different valve anatomies. BAV-A is characterized by smaller diameters, higher biomechanical stress, and significant collagen deterioration, underscoring the necessity for tailored clinical strategies for effective management of thoracic aortic aneurysm.
  • No Thumbnail Available
    Item
    The fusion of tissue spheroids attached to pre-stretched electrospun polyurethane scaffolds
    (2014-01-17) Beachley, Vince; Kasyanov, Vladimir; Nagy-Mehesz, Agnes; Norris, Russell; Ozolanta, Iveta; Kalejs, Martins; Stradins, Peteris; Baptista, Leandra; da Silva, Karina; Grainjero, Jose; Wen, Xuejun; Mironov, Vladimir; Biomehānikas zinātniskā laboratorija
    Effective cell invasion into thick electrospun biomimetic scaffolds is an unsolved problem. One possible strategy to biofabricate tissue constructs of desirable thickness and material properties without the need for cell invasion is to use thin (<2 µm) porous electrospun meshes and self-assembling (capable of tissue fusion) tissue spheroids as building blocks. Pre-stretched electrospun meshes remained taut in cell culture and were able to support tissue spheroids with minimal deformation. We hypothesize that elastic electrospun scaffolds could be used as temporal support templates for rapid self-assembly of cell spheroids into higher order tissue structures, such as engineered vascular tissue. The aim of this study was to investigate how the attachment of tissue spheroids to pre-stretched polyurethane scaffolds may interfere with the tissue fusion process. Tissue spheroids attached, spread, and fused after being placed on pre-stretched polyurethane electrospun matrices and formed tissue constructs. Efforts to eliminate hole defects with fibrogenic tissue growth factor-β resulted in the increased synthesis of collagen and periostin and a dramatic reduction in hole size and number. In control experiments, tissue spheroids fuse on a non-adhesive hydrogel and form continuous tissue constructs without holes. Our data demonstrate that tissue spheroids attached to thin stretched elastic electrospun scaffolds have an interrupted tissue fusion process. The resulting tissue-engineered construct phenotype is a direct outcome of the delicate balance of the competing physical forces operating during the tissue fusion process at the interface of the pre-stretched elastic scaffold and the attached tissue spheroids. We have shown that with appropriate treatments, this process can be modulated, and thus, a thin pre-stretched elastic polyurethane electrospun scaffold could serve as a supporting template for rapid biofabrication of thick tissue-engineered constructs without the need for cell invasion.